logo
Blog
Casa > Blog > AZIENDA blog su Understanding Transformer Test Results During Routine Maintenance
Eventi
Contattici

Understanding Transformer Test Results During Routine Maintenance

2026-11-19

Ultime notizie aziendali su Understanding Transformer Test Results During Routine Maintenance
Transformer Maintenance

Understanding Transformer Test Results During Routine Maintenance

A ratio of 1.002 is not a verdict. Neither is an insulation resistance of 4 GΩ. Results only mean something against a baseline, a temperature and a comparison.

Reading time about 17 minutes | For maintenance engineers and test technicians working on distribution and power transformers

Routine maintenance produces numbers: ratio deviations, resistance values, insulation resistance, oil breakdown voltage. The hard part is not measuring them. It is deciding whether a number describes a healthy transformer, a measurement problem, or a developing fault. That decision depends on four things - the reference the result is compared against, the temperature it was taken at, the pattern across phases and taps, and whether another test supports the same conclusion.

Why a single result rarely proves anything

Transformer tests are comparative by design. A ratio test compares a measured ratio with a nameplate value. A resistance test compares phases with each other and with factory data. An insulation test compares today with last year. Remove the comparison and the number loses most of its meaning.

This is why two identical readings can mean different things. An insulation resistance of 4 GΩ is unremarkable on a 10 MVA unit that read 5 GΩ last year, and alarming on a small unit that read 40 GΩ. The absolute value is not the signal; the direction and the size of the change are.

The four baselines to compare against

  1. Nameplate and factory test report. The only reference for ratio, impedance and design values. If the factory report is missing, the first test after commissioning becomes the reference - and should be labelled as such.
  2. The previous test on the same unit. The most useful reference for insulation and resistance, provided the test conditions were recorded.
  3. Phase-to-phase comparison. On a three-phase unit, the phases should behave similarly. A difference between phases is more informative than any single phase value.
  4. A sister unit. Identical transformers in the same station, under similar load, offer a rough reference when no history exists.

All four collapse if the test conditions are not recorded. Temperature, tap position, test voltage and instrument are part of the result, not optional notes.

Turns ratio: what the number is telling you

The ratio test energises one winding and measures the induced voltage on another, then compares the result with the nameplate ratio for the tap in use. Modern three-phase testers also determine the vector group and the interphase angle, which is often more valuable than the ratio itself: a wrong vector group will trip a differential relay even when every ratio is correct.

Reading the deviation

Deviation is normally expressed as a percentage of the nameplate ratio:

Ratio deviation

Deviation (%) = (Measured ratio − Nameplate ratio) / Nameplate ratio × 100

Measured ratio: tester reading at the tap position under test

Nameplate ratio: marked ratio for the same tap position

A small consistent deviation across all phases and all taps is usually a measurement or nameplate issue: the nameplate ratio may be quoted at a different tap, the tester may be set to the wrong vector group, or the winding may be connected differently from the drawing. A deviation that changes with tap position points at the tap changer. A deviation on one phase only points at that phase's winding, its leads or its tap connection.

Worked example

Nameplate ratio at tap 5: 33.00 kV / 11.00 kV = 3.000

Measured ratio: 3.006

Deviation = (3.006 − 3.000) / 3.000 × 100 = +0.20 %

Whether 0.20% is acceptable is not decided by the size of the number alone. Under IEC 60076-1, the permitted voltage-ratio deviation at the principal tapping is the lower of ±0.5% of the specified ratio or one-tenth of the actual percentage impedance. Requirements for other tapping positions and for additional winding pairs also apply, and national standards or purchase specifications may add their own limits. Check the criterion against the edition of the standard in force for the unit, not against a remembered figure.

Patterns worth recognising

PatternFirst hypothesisNext step
All phases deviate equally at one tap onlyTap changer position or tap contactRepeat at adjacent taps, inspect tap changer
One phase deviates at every tapWinding turns, lead connection or tap leadResistance test on the same phase; check leads
Deviation grows towards one end of the tap rangeTap winding or tap selector faultFull tap sweep, compare with factory tap data
All phases deviate in the same direction by a similar amountNameplate basis, tester setting, vector groupVerify nameplate, test setup and connections before condemning the unit
Ratio correct but angle wrongVector group or phase identificationCheck nameplate vector group and lead marking

Ratio alone cannot distinguish a shorted turn from a tap problem. It narrows the search; resistance and, where justified, excitation current or SFRA complete it.

Winding resistance: the temperature problem

DC resistance proves winding continuity, joint quality and tap contact condition. It is also the test most often misread, because resistance changes with temperature at roughly 0.4% per degree Celsius for copper. A reading taken in a cold substation in winter and compared with a summer reading will show a difference that has nothing to do with the transformer.

Correcting to a common temperature

Results are compared at a reference temperature, usually 75 °C for distribution and power transformers, using the standard correction:

Temperature correction

R2 = R1 × (K + t2) / (K + t1)

R1: measured resistance at temperature t1

R2: resistance corrected to the reference temperature t2

t1: winding temperature during measurement (°C)

t2: reference temperature, usually 75 °C

K: 235 for copper windings, 225 for aluminium windings

The constant follows the winding material: 235 for copper and 225 for aluminium. Some standards use 234.5 for copper, which changes the corrected value by well under 0.1% at normal test temperatures. What matters is that one convention is used consistently across the fleet and stated in the report.

Worked example

Measured: 0.4215 Ω at 18 °C, copper winding

R75 = 0.4215 × (235 + 75) / (235 + 18)

R75 = 0.4215 × 310 / 253 = 0.5165 Ω

For three phases: 0.5165, 0.5148 and 0.5201 ohm. Average 0.5171 ohm, spread 0.0053 ohm, imbalance 1.0%. A 1% spread on a distribution transformer would not normally trigger action on its own; many utilities use around 2% between phases as an investigation trigger, with tighter limits for larger units and for specifications that call for them. The absolute values still have to be compared with factory data at the same reference temperature.

What the pattern suggests

  • One phase high and stable: a joint, a tap contact or a lead connection. Check the connection before suspecting the winding.
  • One phase high and drifting upward across tests: a developing contact resistance problem. This is the pattern worth acting on.
  • All phases high by a similar proportion: usually a temperature or measurement issue, including a winding that has not cooled to ambient.
  • Erratic readings that never stabilise: the winding is still inductive, the current has not settled, or the leads are poorly connected. Do not record an unstable value as a result.
Discharge before disconnecting. The winding stores energy. Follow the instrument's discharge procedure and confirm the discharge before removing leads; an inductive kick is both a safety hazard and a way to damage the tester.

Insulation resistance and polarization index

Insulation resistance is measured between windings and between each winding and earth, at a test voltage appropriate to the winding rating. The reading reflects moisture, contamination and insulation condition, and it is strongly temperature dependent: insulation resistance roughly halves for every 10 °C rise in oil temperature, which is why a hot reading and a cold reading are not comparable.

Reading the numbers

For oil-immersed transformers, the polarization index compares the resistance at ten minutes with the resistance at one minute:

Polarization index

PI = R10 min / R1 min

R10 min: insulation resistance after 10 minutes of applied test voltage

R1 min: insulation resistance after 1 minute

PI describes how strongly the insulation polarizes, which is a function of insulation type, condition and temperature. A PI near 1.0 on oil-paper insulation usually warrants investigation, but a low PI is not proof of a fault: dry-type and resin-cast windings polarize weakly by nature, and a measurement taken at high temperature or with a short stabilization time can produce the same result on healthy insulation.

This is where insulation type matters more than any single threshold. Oil-paper, resin-cast and liquid-filled windings behave differently, and a limit copied from one type applied to another produces false alarms. Compare with the previous test on the same unit, at a similar temperature, with the same test voltage and duration.

Practical checks before condemning the insulation

  • Was the surface clean and dry? Bushing contamination produces a low reading that cleaning removes.
  • Was the guard terminal used where surface leakage is significant?
  • Was the oil temperature recorded, and is the comparison made at a similar temperature?
  • Did the reading stabilise, or was it still rising when recorded?
  • Were the bushings, arrester connections and neutral connections isolated as required?

An insulation result that contradicts the oil results and the visual inspection deserves a repeat measurement before it becomes a maintenance decision.

Oil breakdown voltage: what it does and does not tell you

For oil-immersed transformers, the oil is part of the insulation system. A BDV test raises the voltage across a defined electrode gap until breakdown; the result is sensitive to moisture and to solid particles suspended in the oil.

What a low BDV means: the oil's dielectric strength has fallen, usually because of moisture ingress or particulate contamination. It does not tell you where the moisture came from, and it does not identify a winding fault. What it does not mean: a low BDV is not evidence of winding deformation, and a good BDV does not prove the insulation is healthy - a transformer with a hot spot and active arcing can still have acceptable bulk oil.

Sample handling decides the value of the result. A sample drawn from a dead-end valve, taken in wet weather without a closed sampling arrangement, or left standing before test can show contamination introduced by the sampling rather than present in the transformer. Record the sampling point, the oil temperature and the time between sampling and test.

BDV is not DGA. Breakdown voltage measures dielectric strength. Dissolved gas analysis identifies decomposition products and requires gas chromatography with its own sampling procedure. A utility that reports "oil test passed" on the strength of a BDV result has not assessed the transformer's internal condition.

Beyond BDV: moisture and oil quality

BDV is a screening measurement, not a full oil assessment. When it falls, the useful next step is water content, acidity and interfacial tension, because these indicate whether the problem is moisture ingress, oxidation or contamination. Water content is the most directly actionable: it tells you whether the oil can be dried in place or whether the insulation itself has absorbed moisture and needs a different decision.

A rising water content with a stable BDV is an early warning. A falling BDV with normal water content points towards particulate contamination or sampling error. Reading the two together prevents the common mistake of treating a single low BDV as proof of a wet transformer.

Typical new-oil acceptance values sit around 30 kV and above for a 2.5 mm gap, but the applicable limit depends on voltage class, oil type and the utility's specification. Treat any single number as a starting point, not a universal pass mark.

SFRA: a comparison, not a measurement

Frequency response analysis sweeps the transformer's impedance over a frequency range and compares the resulting curve with a reference. It detects winding deformation, core movement and winding displacement that ratio and resistance tests cannot see.

The method is described in IEC 60076-18 and is inherently comparative. Without a baseline - factory data, an earlier test or a sister unit - a single curve has limited diagnostic value, because normal transformers differ in their response. Interpretation also requires experience: connection quality, earthing, tap position and even the test lead layout change the curve.

SFRA is not a routine test for every distribution transformer. It is used after a through-fault, a transport event, a repair, or when other results suggest mechanical movement. When it is used, repeat the measurement with identical connections before drawing a conclusion.

When to repeat before deciding

Some results should not be acted on until they are repeated. Repeat the measurement, on the same tap and at a recorded temperature, when:

  • the value contradicts the other tests on the same unit;
  • the reading had not stabilised when it was recorded;
  • the test conditions were unusual - wet weather, recent load change, oil not settled, cold winding;
  • the deviation is small enough to sit inside the instrument's accuracy and the temperature correction;
  • a lead, connection or guard arrangement was changed between tests.

A repeat test costs an hour. Replacing a transformer because of a contaminated bushing, a loose lead or an uncorrected temperature difference costs considerably more. Where the repeat confirms the result, the second measurement also gives you the trend point you will need next year.

Reading the results together

The value of routine maintenance comes from combining tests, not from any one of them. The table maps common combinations to the most likely explanations.

Combination of resultsMore likely explanationConfirm with
Ratio deviation on one phase, resistance high on the same phaseTap contact or winding connection faultTap sweep, inspection
Ratio normal, resistance imbalance, insulation normalJoint or tap contact resistanceRepeat resistance at stable temperature
Insulation resistance low, PI low, oil BDV lowMoisture in the insulation systemOil moisture content, drying decision
Insulation resistance low, oil BDV normalSurface contamination, bushings or leadsClean and repeat, check bushings
All electrical tests normal, DGA abnormalLocalized thermal or discharge fault not yet affecting bulk measurementsDGA trend, repeat sampling
Ratio and resistance normal, SFRA deviatesWinding movement without turn lossRepeat SFRA, compare phases

The table is a reasoning aid, not a diagnosis. Every row assumes the measurement was valid, the temperature was recorded, and the comparison basis was correct.

Common interpretation errors

  • Judging a result without a baseline. A number with no reference is a data point, not a finding.
  • Ignoring temperature. Resistance and insulation resistance both move with temperature; an uncorrected comparison invents faults.
  • Comparing different tap positions. A ratio measured at tap 3 and a factory value at tap 5 will disagree for legitimate reasons.
  • Treating PI as a universal pass mark. Insulation type, temperature and test duration change the value.
  • Confusing oil BDV with DGA. They answer different questions and are not interchangeable.
  • Condemning a transformer on one test. Ratio, resistance, insulation, oil and SFRA are meant to be read as a set.
  • Recording unstable readings. A resistance that is still falling is not a result.

What belongs in the report

A maintenance report that cannot be compared with the next one is of limited use. Record the tap position, oil or winding temperature at the time of test, the test voltage and duration for insulation tests, the instrument and its calibration status, the reference temperature used for correction, and the factory or previous values the result is compared against. Add a short interpretation: what changed, by how much, and what the next action is.

Key takeaways

  1. Transformer results are comparative: nameplate, previous test, phase comparison and sister units are the references.
  2. Ratio deviation patterns narrow the fault; they do not identify it on their own.
  3. Winding resistance must be corrected to a common temperature before any comparison.
  4. PI depends on insulation type; a low value is a prompt to investigate, not a verdict.
  5. Oil BDV measures dielectric strength, not internal condition; DGA is a separate test.
  6. SFRA is a comparative diagnostic, used when there is a reason and a baseline.

Frequently asked questions

What ratio deviation is acceptable on a distribution transformer?

There is no single figure that applies to every unit and every tap. Under IEC 60076-1, the limit at the principal tapping is the lower of ±0.5% of the specified ratio or one-tenth of the actual percentage impedance, with separate requirements for other tap positions and winding pairs. The purchase specification and the standard edition in force decide the acceptance criterion. A deviation inside tolerance can still matter if it has changed since the last test.

Why does winding resistance change so much between seasons?

Copper resistance rises about 0.4% per degree Celsius. A transformer measured at 5 °C in winter and at 35 °C in summer will show roughly a 12% difference with no fault present. Correct both readings to the same reference temperature before comparing.

Is a polarization index below 1.5 always a problem?

No. PI depends on insulation type, temperature and test duration. Dry-type and resin-cast windings polarize weakly, and a hot measurement can lower PI on healthy insulation. Compare with the unit's own history at a similar temperature before concluding that the insulation has deteriorated.

Does a good oil BDV result mean the transformer is healthy?

No. BDV measures the dielectric strength of the bulk oil against moisture and particles. It does not detect localized thermal or discharge faults, which dissolved gas analysis is intended to reveal. A transformer can pass BDV and still have an active internal fault.

When should SFRA be performed?

When there is a reason: after a through-fault, during transport or after a repair, or when ratio, resistance or DGA results suggest mechanical movement. It requires a baseline and identical test connections, and it is interpreted by comparison rather than against a fixed limit.

Can one test result justify removing a transformer from service?

Rarely. A single result should be repeated and supported by another test before an outage decision. The exception is a result that indicates an immediate safety risk, such as a very low insulation resistance with visible damage or an active internal fault confirmed by gas analysis.

Equipment for transformer maintenance testing

Interpreting a result you are not sure about?

Send the test values, the tap position, the oil temperature and the previous report. We will help you work out whether the change is a measurement artifact, a normal trend or something that needs an outage.

Scope note: this article describes general interpretation practice. Acceptance limits, test voltages, correction factors and maintenance intervals come from the applicable standards (including IEC 60076 series, IEC 60156, IEC 60422 and IEEE C57.12.90), the transformer manufacturer's instructions, the purchase specification and the utility's own policy. Values quoted here are typical examples, not universal requirements.

Invia la tua richiesta direttamente a noi